rj12

Anyone who has ever used a desk or wall phone knows they all have one problem in common: cords getting tangled. In the long run, it does not particularly matter how careful or gentle you are with a coiled handset cord. Eventually, the cord is going to end up as a jumbled mess. Preventing a cord from tangling in the first place is where a detangler comes in.

Phone cords do not last forever. When a cord starts to tangle, the smaller wires inside the cord begin to bend the wrong ways and start developing small, unnoticeable kinks. While the damage does not have immediate effects, it does add up over time. Eventually, the phone cord will start to have static because the damaged telephone wire can no longer transmit a phone signal properly.

Along with a static-filled signal, tangled cords are just annoying. You sit there trying to keep the cord straight as it wraps around itself, wraps around your hand, and knocks a picture frame off the table all while the damage keeps compiling. Eliminating this issue is arguably even more important than using a detangler to extend the life of the phone cord.

Functionally, a cord detangler is very simple. The detangler goes in-between the handset and the coiled cord. One side of the detangler plugs into the handset (where the phone cord would plug in normally) and then the phone cord goes into the other end of the detangler. The part of the detangler connected to the phone cord spins around, preventing the

Modern telephone cords have been in use for a long time, with little change since their invention in the 1970s. Finding phone cords in the store can be tricky today; many stores have stopped carrying telephone cables since so many people only use cell phones now. This rings especially true for coiled handset cords. With these cables becoming rarer, sometimes it is better to repair rather than replace them. Other times, users may just need a cable not available in a standard length.

There is a bit of variation with different connectors available, as well as different wiring schemes (called pinouts) for the smaller wires inside the main cord. This guide will cover how to attach a connector to the end of bare telephone wire and the difference between wiring pinouts.

Step 1: Gathering the Supplies

There are a few simple supplies that will be needed for an installation or repair. The key components are the bare phone cable and the correct type of connectors. There are three main types of connectors that can be used. RJ12 is the most common, being used on flat line cords that connect the base of a telephone to the wall. RJ11 is an older version of RJ12, and they are the same size. The difference is that RJ11 uses four internal wires (called conductors) while RJ12 cable uses six. RJ12 is backwards compatible with RJ11, but RJ11 will not work with RJ12.

Coiled

Telephone cords are one of the more basic types of cables. Phone cables have remained mostly the same over the years with a few small changes here and there. There is a little terminology to know that will tell you a bit more about your phone lines, such as how they are wired and what type of plastic connector is on the end of the cable.

Phone cords come in two varieties, flat cords used to connect phones to the wall and coiled cords used for handset receivers. Flat cords will use either an RJ11 or RJ12 connector. These two connectors are the same size and look the same on the outside. On the inside, RJ11 will have four metal contacts for the internal wires inside the cable while RJ12 cable has six contacts. Since they are the same size, RJ12 is backwards compatible with RJ11. However, since RJ11 is the older of the two it is not compatible with RJ12.

The next distinction is whether your flat cord is straight or reverse. Straight cables are used to send data, like a fax machine, while reverse cables are used for voice, like a telephone. On a straight cable, the telephone wire will connect to the same metal pins on either side of the cable. Pin 1 to pin 1, pin 2 to pin 2, etc. On a reverse cable, the opposite is true. For RJ12, a reverse cable would go pin 1 to pin 6, pin 2 to pin 5, etc.

Round versions of the flat cord also exist but are usually used for something other than a phone. Typically, they are equipped with extra features that make them larger than the average flat cable, such as something built for outdoor use or a cable designed to connect an Internet modem to a wall jack.