SATA to SATA Cable - Dual Right Angle
SATA Computer Cable - 1M Dual Right Angle SATA Cable
This 1 meter 7-pin SATA Cable with two right angled connector is used to connect SATA devices, such as internal hard drives, to your computer's motherboard. The angled end makes connection in tight spaces easier while also relieving stress on the connector. It allows for transfer rates of up to 6 gigabits per second. This SATA cable will reduce crosstalk and give you high signal integrity delivering better performance. The SATA cable has a long, slim design that allows for easier cable routing, increases airflow which reduces the chance of overheating, and saves space by minimizing internal clutter.
- Connector 1: SATA 7-pin - Right Angled
- Connector 2: SATA 7-pin - Right Angled
- SATA 3.0 Compatible
- Transfer Rates up to 6G
- Reduced Crosstalk
- High Signal Integrity
- Slim Design to Promote Air Circulation
- Length: 1 Meter
- Color: Red
- RoHS Compliant
WARNING: This product can expose you to chemicals including phthalates, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
Directive on the restriction of the use of certain hazardous substances in electrical and electronic equipment in the European Union. It stands for Restriction of Hazardous Substances Directive.
REACH, a European Union regulation addresses the production and use of chemical substances and their potential impacts on both human health and the environment. It stands for Registration, Evaluation, Authorisation, and Restriction of chemicals.
The WEEE Directive set collection, recycling and recovery targets for all types of electrical goods in the European community. It stands for Wate Electrical and Electronic Equipment Directive.
* The following information is for information purposes only. It does not guarantee that the product adheres to the following standards. Please check the product description for specific certifications.
Q: What is SATA?
A: SATA cables are the new connector type that is replacing the older Parallel ATA interfaces. SATA cables allow for faster data transfer rates and offer a direct connection between the hard drive and the motherboard. SATA cables are longer and thinner than its predecessor which uses short fragile and bulky cables. This allows for a much better performance from the SATA cables.
Q: What is the difference between a SATA Cable and an eSATA cable?
A: SATA and eSATA cables are very similar and they operate at the same speeds of up to 6Gb/s. The main difference between the two is that SATA cables are for internal use and eSATA cables are for external use. The eSATA cables are built with shielded cable so that they can withstand an external environment and be used more ruggedly.
Q: What is the difference between the SATA cables the SAS InfiniBand cables you sell?
A: SAS InfiniBand cables are backwards compatible with SATA cables. This means you are able to connect SATA drives to SAS backplanes. SAS cables are more costly and are often used in more critical server applications. The SAS cables allow for higher signal voltages so they can be much longer than SATA cables. This gives users more versatility when connecting applications.
Q: What are the maximum lengths for SATA eSATA and SAS InfiniBand cables?
A: SATA cables are no longer than 1 meter (3.3 feet) in length. eSATA cables can be longer due to their rugged design. They are typically as long as 2 meters (6 feet) in length. This allows them to be able to reach from the floor to the desktop. SAS InfiniBand cables can go the longest distances. They can be up to 10 meters in length.
Q: I am looking to connect my external hard drive to my motherboard. Which is better; an eSATA or USB cable?
A: eSATA cables will support faster transfer speeds at least three times as fast as USB cables. They are more reliable and offer a much better performance than their alternatives.
Q: I have two hard drives on my computer? What do I need to connect these two?
A: SATA cables can be used to connect your two hard drives together. After you have them connected you can adjust the SATA ports on your hard drives and decide which hard drive you want to be the primary one and which you want to be the secondary or back-up hard drive.
|Features & Specs|
|Connector 1||The type of connector on side 1?||SATA Right Angle|
|Connector 2||The type of connector on side 2?||SATA Right Angle|
|Pins||The number of pins in the connector?||7-pin|
|Transfer Rate||The speed at which the data can travel?||Up to 6Gb/s|
|Gauge||The size of the copper wire?||26 AWG|
|Conductors||What material is used for the conductors?||Copper|
|Material||The material used for the jacket?||PVC|